Miller - (907335011)

• 10 ft (3m) M-100 Miller MIG gun
• 10 ft (3 m) work cable with clamp
• Factory-installed gas solenoid valve
• Smith® Argon and AR/CO2 mix regulator/flow gauge and gas hose
• 6 ft (1.8 m) power cord and plug
• Two contact tips for .024 in (0.6 mm) wire and two contact tips for .030 in (0.8 mm) wire
• Dual groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) wire
• Spool of Hobart® .030" solid wire
• Information/settings chart
• Set-up and operation video
• Material thickness gauge

• All-in-one wire welding package welds 24 gauge - 3/16 in (0.8 - 4.8 mm) mild steel. The simplest Millermatic to set-up and start welding.

• New! Auto-Set™ is a breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG, minus the guesswork! Simply set the wire diameter, set the material thickness, and start welding!

• Manual Mode has the flexibility to manually set weld parameters for broader applications.

• NEW! Smooth-Start™ patent-pending technology provides a smooth, spatter-free start. —The best starting machine in the small MIG category. No more pop-gun starts or spatter to clean up.

• Durable cast aluminum feedhead incorporates dual groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob, all designed to make setup easier and faster.

• Thermal Overload Protection shuts down the unit and activates over- temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools.

• "Tip Saver" short circuit protection shuts down output when tip is shorted to the work. Extends contact tip life and protects internal components from damage. Trigger reset permits quick reset at torch rather than unit.

• Standard Built-in solid-state contactor circuit makes wire electrically "cold" until trigger is pulled. Makes unit safer, and is easier to position torch to work before starting to weld.

• Easy access to output studs provides convenient polarity changeover when switching from solid or flux cored wires.

• Self-resetting motor protection circuit eliminates the need to find and replace fuses.

• Uses 4 or 8 in (102 or 203 mm) spools and can be set up to weld with wire sizes .024 - .030 in (0.6 - 0.8 mm) mild/stainless steel and .030 - .035 (0.8 - 0.9 mm) flux cored.

• Note: Auto-Set is calibrated for .024 and .030 mild steel wire and C25 shielding gas (75% Argon, 25% CO2). Use manual mode for broader applications with mild steel, or to weld stainless steel or flux core.

Detailed specs for Miller

• Requires 1-Phase power
• 115 V, 20 Amps 60Hz

• 90A at 18 VDC, 20% duty cycle

• 30 - 140 Amps

• 15 - 390 IPM (1.0 - 12.7 m/min)

• 60lb (27.3kg)

Resources for Miller

Manufacturer's Resources

- Product Fact Sheet
- Owner's Manual
- Warranty Information
- Miller MIG Welding Resources

General Welding Information

- Common Welding Supplies
- Welding Equipment
- Welding Fume Ventilation
- Welding Gear and Safety Tips

MIG Welding Articles

- Common MIG Weld Defects
- Tips on MIG Troubleshooting
- MIG Welding Settings
- MIG Welding Wire Feeder Selection
- Tips on How to MIG Weld
- MIG Shielding Gas Selection Guide
- MIG Welding Advantages/Disadvantages

MIG Welding How-to Videos

- MIG Uphill Welding Technique
- MIG Welding Principles

Home Welding Projects

- How to Weld a Table
- How to Make Extra Money from Welding Projects
- Video-How to Weld Dining Room Chairs
- Hobby Welding Projects for Beginners
- Welding a Dolly
- Small Welding Projects from Scrap
- Some Project Ideas
- Beginner Welding Projects
- Shop Stool
- Fun Welding Projects
- Reusable Welding Jig
- Video-Finishing Welding Projects with Proper Post Weld Cleaning
- Christmas Welding Projects