Miller Millermatic 211 All-In-One MIG Welder w/ Auto Set and MVP Plug w/ Cart(120/230 V) - (951375)

• Power source
• 6 ft (1.8 m) power cord and MVP plugs
• 10 ft (3 m) M-100 MIG gun and cable assembly
• 10 ft (3 m) work cable and clamp
• Smith Argon and AR/CO2 mix regulator/flow gauge with hose
• Spool of Hobart .030 in (0.8 mm) solid wire
• Two contact tips for .030 in (0.8 mm) wire and two contact tips for .035 in (0.9 mm) wire
• Dual groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) wire
• Factory-installed gas solenoid valve
• Set-up and operation CD
• Information/settings chart
• Material thickness gauge

• All-in-one wire welding package welds 24 gauge - 3/8 in (0.8 - 7.9 mm) mild steel.

• New! Auto-Set is a breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG, minus the guesswork for .030/.035 steel.

• Welds thickest material in its class, with the highest output in its class! Can weld up to 3/8 inch in a single pass at 230 V.

• Spool gun ready out of the box! The new Spoolmate 100 Series spool gun allows you to weld from 18 gauge to 3/8 inch aluminum.

• New! Smooth-Start patent-pending technology provides a smooth, spatter-free start. The best starting machine in the small MIG category. No pop-gun starts or spatter to clean up.

• Durable cast aluminum feedhead incorporates dual groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob all designed to make setup easier and faster.

• Thermal overload protection shuts down the unit and activates over temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools.

• Miller's exclusive "Tip Saver" short circuit protection shuts down output when tip is shorted to the work. Extends contact tip life and protects internal components from damage. Trigger reset permits quick reset at torch rather than unit.

• Standard built-in solid-state contactor circuit makes wire electrically "cold" until trigger is pulled. Makes unit safer, and is easier to position torch to work before starting weld.

• Easy access to output studs provides convenient polarity changeover when switching from solid or flux cored wires

• Self-resetting motor protection circuit eliminates the need to find and replace fuses.

• Uses 4 or 8 in (102 or 203 mm) spools and can be set up to weld with wire sizes .024-.035 in (0.6-0.9 mm) mild/stainless steel and .030-.045 in (0.8-1.2 mm) flux cored.

Detailed specs for Miller Millermatic 211 All-In-One MIG Welder w/ Auto Set and MVP Plug w/ Cart(120/230 V)

• Requires 1-Phase Power
• 120 V, 20 A, 60 Hz
• 230 V, 25 A, 60 Hz

• 90 A at 20 VDC, 20% Duty Cycle (120V)
• 150 A at 23.5 VDC, 30% Duty Cycle (230V)

• 30 - 210 Amps

• 60 - 460 IPM (1.5 - 11.7 m/min)

• 74 lb (33 kg)

Miller Millermatic 211 All-In-One MIG Welder w/ Auto Set and MVP Plug w/ Cart(120/230 V) comes complete with:

• Power source
• 6 ft (1.8 m) power cord and MVP™ plugs
• 10 ft (3 m) M-100 MIG gun and cable assembly
• 10 ft (3 m) work cable and clamp
• Smith® Argon and AR/CO2 mix regulator/flow gauge with hose
• Spool of Hobart® .030 in (0.8 mm) solid wire
• Two contact tips for .030 in (0.8 mm) wire and two contact tips for .035 in (0.9 mm) wire
• Dual groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) wire
• Factory-installed gas solenoid valve
• Set-up and operation CD
• Information/settings chart
• Material thickness gauge

Resources for Miller Millermatic 211 All-In-One MIG Welder w/ Auto Set and MVP Plug w/ Cart(120/230 V)

Manufacturer's Resources

- Product Fact Sheet
- Owner's Manual Search
- Warranty Information
- Miller MIG Welding Resources

General Welding Information

- Common Welding Supplies
- Welding Equipment
- Welding Fume Ventilation
- Welding Gear and Safety Tips

MIG Welding Articles

- Common MIG Weld Defects
- Tips on MIG Troubleshooting
- MIG Welding Settings
- MIG Welding Wire Feeder Selection
- Tips on How to MIG Weld
- MIG Shielding Gas Selection Guide
- MIG Welding Advantages/Disadvantages

MIG Welding How-to Videos

- MIG Uphill Welding Technique
- MIG Welding Principles

Home Welding Projects

- How to Weld a Table
- How to Make Extra Money from Welding Projects
- Video-How to Weld Dining Room Chairs
- Hobby Welding Projects for Beginners
- Welding a Dolly
- Small Welding Projects from Scrap
- Some Project Ideas
- Beginner Welding Projects
- Shop Stool
- Fun Welding Projects
- Reusable Welding Jig
- Video-Finishing Welding Projects with Proper Post Weld Cleaning
- Christmas Welding Projects